Titan Mining Drills Two New Zones of Near-Surface Mineralization, Including 80 Feet of 5.8% Zinc, 2.8% Lead and 28.2 g/t Silver - Seite 4

• 80.0 feet assaying 5.8% zinc, 2.8% lead and 28.2 g/t silver
  ◦  Including 15.0 feet assaying 17.1% zinc, 7.8% lead and 79 g/t silver

Notable mineralized interval from SX19-2485 was:

• 50.0 feet assaying 1.4% zinc, 0.4% lead and 5.0 g/t silver
  ◦  Including 10.0 feet assaying 3.6% zinc, 0.9% lead and 6.4 g/t silver

For a full list of the Hoist House and Turnpike mineralized intervals from these holes, refer to Table 1.

Figure 1 – Location of Near-Surface Drill Targets at ESM
https://www.globenewswire.com/NewsRoom/AttachmentNg/0763157e-04f6-48c6 ...

Figure 2 – Plan View of Hoist House and Turnpike Zones Showing Drill Hole Locations
https://www.globenewswire.com/NewsRoom/AttachmentNg/4f328500-109b-4c18 ...

Figure 3 – Cross Section of Hoist House Zone Looking Northeast and Showing Drill Holes and Selected Mineralized Intervals
https://www.globenewswire.com/NewsRoom/AttachmentNg/91c64f06-ec61-4657 ...

Figure 4 – Cross Section of Turnpike Zone Looking Northeast and Showing Drill Holes and Selected Mineralized Intervals
https://www.globenewswire.com/NewsRoom/AttachmentNg/2b401e1d-ac75-48c2 ...

Table 1 – Exploration Drill Results from Hoist House and Turnpike Zones at ESM
https://www.globenewswire.com/NewsRoom/AttachmentNg/7e42d21c-089f-4e41 ...
^* Based on observed geologic contacts, no representation is made here regarding the true width.

Qualified Person

The results of the Titan drilling have been reviewed, verified and compiled by Donald R. Taylor, MSc., PG, Chief Executive Officer of Titan, a qualified person as defined by National Instrument 43-101 (NI 43-101). Mr. Taylor has 30 years of mineral exploration and mining experience, and is a Registered Professional Geologist through the SME (registered member #4029597).

Assays and Quality Assurance/Quality Control

To ensure reliable sample results, the Company has a rigorous QA/QC program in place that monitors the chain-of-custody of samples and includes the insertion of blanks and certified reference standards at statistically derived intervals within each batch of samples. Core is photographed and split in half with one-half retained in a secured facility for verification purposes.

Sample preparation (crushing and pulverizing) has been performed at ALS Geochemistry, an ISO/IEC accredited lab located in Sudbury, Ontario, Canada. ALS Minerals Laboratories prepares a pulp of all samples and sends the pulps to their analytical laboratory in Vancouver, B.C., Canada, for analysis. ALS analyzes the pulp sample by an aqua regia digestion (ME-ICP41 for 35 elements) with an ICP – AES finish including Cu (copper), Pb (lead), and Zn (zinc). All samples in which Cu (copper), Pb (lead), or Zn (zinc) are greater than 10,000 ppm are re-run using aqua regia digestion (Cu-OG46; Pb-OG46; and Zn-OG46) with the elements reported in percentage (%). Silver values are determined by an aqua regia digestion with an ICP-AES finish (ME-ICP41) with all samples with silver values greater than 100 ppm repeated using an aqua regia digestion overlimit method (Ag-OG46) calibrated for higher levels of silver contained. Gold values are determined by a 30 g fire assay with an ICP-AES finish (Au-ICP21).